How to request and install a Flow-Xpress License

How to request and install a Flow-Xpress License

HOW TO INSTALL FLOW XPRESS SOFTWARE & LICENSE
HOW TO INSTALL FLOW XPRESS SOFTWARE & LICENSE
To download the Flow Xpress software go to the download site at https://www.crt-services.com/support/. Once the software is downloaded, please complete the installation of the software. One of the last steps of installing the software packages required you to provide details about the installed software. In case of a personal license use the following:

  • End-User: Your name
  • Company: Name of your company
  • Serial Number: Serial number of module working on  

After installing the software and completing the details press OK and start the ‘License Manager’ from the Program Files. In order to provide you the correct authorization details, Spirit IT requires the Export file of this specific system. These details can be extracted using the ‘Export ’ button within the License Manager and press ‘Save’ to actually save the export file to your hard drive.

You need to send the Export file to CRT by contacting their license support group at service@crt.services Within this e-mail state clearly:  Flow-Xpress professional When your authorization request has been approved you will receive a digital End-User License Agreement containing the License details. On receipt of the certificate, please check the details on the document and notify CRT if the certificate is not correct.

The End-User License Agreement contains the Authorization key and License number enter these into the License Manager and press ‘Install’ to authorize your system. You will get a popup with the message whether the Authorization has been completed successfully. If so, close the License Manager and start using the installed Spirit IT software.

    • Popular Articles

    • How to connect prover signals

      CONNECT PROVER SIGNALS In this HowTo will be explained how prover signals should be connected. This depends on the Flow-X type and the prover setup. Flow-X/P Ball prover / Compact prover. Connect the flow pulse signals to the corresponding modules ...

    • How to print a snapshot report on startup in Flow-X

      PRINT A SNAPSHOT REPORT ON STARTUP IN FLOW-X This document describes how to generate a snapshot repot whenever the Flow-X flow computer starts up for any reason. Define a new Calculation group Define a new tag to latch the latest startup time Give ...

    • Adding new users to the FlowX

      Security Files In Flow-Xpress users and passwords can be modified and added both in online mode (directly in the flow computer, also for multiple flow computers at once) and offline mode (in the loaded application file). Each user has a specific ...

    • USE MODBUS SLAVE WHILE READING VALUES FROM A DEVICE

      When using the Modbus Slave protocol, a synchronization problem may occur while reading values from a device. This HowTo explains how to overcome this problem. 

    • SET UP FLOW COMPUTERS IN COMBINATION WITH A PROLINX DEVICE

      This How To explains how you can set up one or more flow computers when a ProLinx device for HART master is also present. The flow computer’s HART master protocol is acting such that the flow computer is either listening or an active sender. When two ...

    • Related Articles

    • How to simulate proving using a FlowX flow computer

      How to simulate proving with the Flow-X flow computer This How to instruction will provide an example of how to program the FlowX to simulate proving a meter. Most newer flow computers require live pulses and detector inputs to prove a meter. Wiring ...

    • Flow-X Ground Wiring

      Ground wiring The Flow-X flow computer uses the following separate ground connections: one common ground for the power supply and the digital signals ('0 V') one isolated common ground for the analog inputs ('Analog input common') one isolated common ...

    • Flow-X Analog output calibration

      The procedure to calibrate an analog output is based on a 4-20 mA meter. 1. Connect the mA meter in series with the load. 2. Go to the analog output calibration display. Display → Diagnostics, IO, <Module x>, Calibration, Analog outputs With x the ...

    • Wiring Hart input to Flow-x

      The first 4 analog input circuits of each Flow-X/M flow module have an on-board HART modem to facilitate HART communication. The Flow-X flow computer uses an internal 250 Ω resistor for its analog inputs, which is adequate for HART communication. The ...

    • SET UP FLOW COMPUTERS IN COMBINATION WITH A PROLINX DEVICE

      This How To explains how you can set up one or more flow computers when a ProLinx device for HART master is also present. The flow computer’s HART master protocol is acting such that the flow computer is either listening or an active sender. When two ...